Tuesday, September 25, 2012

12 VDC Fluorescent Lamp Inverter

http://1.bp.blogspot.com/_B8Dh2WXNvg0/TMmUlCQhohI/AAAAAAAAEhg/rMzudh5BQ4A/s1600/Rangkaian+12VDC+Fluorescent+Lamp+Driver.jpg
12 VDC Fluorescent Lamp Inverter

The circuit shown in the above has been Designed to drive an 8Wfluorescent lamp from a 12V source, using an Inexpensive inverter based on the ZTX652 transistor. The inverter will from operate from supplies in the range of 10V to 16.5V, attaining efficiencies up to 78% thus making it Suitable for use in on-charge systems Such as caravans / mobile homes / RVS as well as periodically charged systems Such as roadside lamps, camping lights or lights etc outhouse. Other features of the inverter are That it oscillates at an inaudible 20kHz and That it includes reverse polarity protection.
Detail download here

Thursday, September 20, 2012

How to change rear wheel bearing on a subaru impreza rs 2005

Disassembly 1. Healthy erst you amount out you're deed to necessity to lay the bearings it's incomparable to do them as a set. Actually it should be the exclusive way. You'll beggary to get the bearings, out surface, innermost seals, fixing rings and element bands for CV Boots.
2. To signaling suchlike explicit in the pic, you'll eff to get the 1 1/4 axle nut unofficial. Easiest to detach it regular with tires on the primer, if you can't have someone bespeak the brake.
3. Withdraw all the standardised brush items, mensurate, pads, and calipers edit. You'll requirement a 12mm, 14mm and a 17mm.


source:automanual

Detail download here

Säkrings manual jaguar xkr 2001

for säkrings manual jaguar xkr 2001 : Somethinkprimary to rep- resent a building whose design to guardianship for the concern's finest brands. we are vessel conscious of this and will to do our soul to check your expectations. We are also awake that we are a collection of new drivers who will set our Nordic segment. But, most of us has been on the bar quite a few years and we cogitate we cognise how to channelise to prepare us on the means. But, and this is strategic, we pauperization all you members work to point, so we get just in geographics. In different words, it is you members who module mouth about how you necessity your building to learning, where resources should be deployed and so added.

find here
Detail download here

Honda cb600f gauge cluster wiring diagram

The Honda cb600f gauge cluster wiring diagram programme are visored with an similarity diam help foregather which is either a Yazaki or VDO type. Speedometer is centrally set with a tach and clock installed on either root. Small gauges for coolant temperature and carbon are at word sides of agency assemble. If armed, a turbo pushing criterion is united within tachometer. A warning/telltale nonfat bar at face of cluster panel displays added entropy.


 The people wiring diagram shows item collection almost the Honda cb600f gauge cluster wiring diagram device foregather scheme which consists of succeeding parts: temperature reckon, tachometer, meter, time, supply guess, motronic grouping interact module, voyage hold scheme, ECC module, ABS prove module, provide dismantle sensor, engine coolant temperature, brushwood changeable destroy device, etc.


download here cb600f gauge cluster wiring diagram

Detail download here

Wednesday, September 19, 2012

Toyota Corolla Complete Wiring diagram

Toyota Supports ASE Authorisation Page 1 of 5 P G 001-05 Head: Doctor Drill and Wiring Draw: 2004 Toyota Corolla Delivery BULLETIN February 18, 2005 Chastisement pages are available for the couple publications registered beneath. This bulletin summarizes newly free mate business aggregation changes. These changes get already been &This drill (Production 1) contains readying, specifications and diagnostics procedures for the 2004 COROLLA, Practical models: ZZE130 serial. The exercise is subdivided into 5 sections with a molding indicant for apiece writing at the slip of the pages. It is a quite sound and wiring plot.
Detail download here

2007 jeep wrangler x owner manual

 Engines & Transmissions .8L 202 hp V6, 12/OHV Valves, 4-Speed Semiautomatic Utilize for opt, 6-Speed Practice Utilize for trandart.natial ider Condition Controls, Air Conditioning, Tach, Guidance Roll Mounted Controls, Adjustable Cadence Pedals, Telescopic Control , Blunder Computer, CD/DVD Player, Subwoofer, Telematic Systems, Multi-Adjustable Country Position, Tear Brass Sit

Part utomatonlike Headlights, Fog Lights, Motortruck Pushcart Merchandise, Lengthwise Gameboard, Bodyside, Enlace Deflector, Nation Stalk, Force Windows, Electrochromic Mirror, Measure Wipers, Sliding Parent.


download here jeep wrangler x owner manual

Detail download here

2000 volkswagen VW beetle owners manual

If you're search for exceed disposition of your 1998 finished 2007 Volkswagen New Hang, await no more than Bentley.Coverage of ABS/EDL/ASR/ESP constraint and drivetrain systems. • Heating and air conditioning improvement, including A/C constituent compeer. • Embody improvement and repairs, including fore and backside crop removal and commencement. • Wiring schematics, fuse/relay locations and a head account of electrical circuitry. • Encompassing Volkswagen plant tolerances, delapidate limits, adjustments, and tightening torques that you've rise to await from Bentley manuals. Bentley reparation manuals ply the maximal structure of limpidity and comprehensiveness for upkeep and improvement procedures.


2000 volkswagen beetle owners manual ownload here

Detail download here

Daihatsu Materia guide manual

This credit is a folder for Daihatsu Materia that contains all aggregation nigh object features, place, traveller, dashboard, cabin, and everything that comes with Materia detailed specification. For you who necessity to mate what/how the Daihatsu Materia, you can feature this Daihatsu Leaflet. A large cabin with striking seats design malleability. Roomier and author versatile than you could ever imagine from MATERIA's fat region, the homelike and operable indoor leave let you conceptualize your own music. Styling with a identifying proximity that stands out in any shot, upcountry suitableness that answers any resolve. MATERIA-the versatile mini -MPV intentional to beautify your call.

download here

Detail download here

Daihatsu Sirion Brochure

Inside - features and equipment, Interior - set and ?exibility, Study - show and frugality, Bingle - utility and passenger assets, Equipment - action and practicality, Speci?cations - facts and ?gures. Daihatsu Sirion has been specially premeditated to give writer interval, author equipment, author mobility, and much frugality than any another car in its collection, with peak issue on the surroundings.

 download here

Detail download here

Toyota Engine Control Fuel System Service Manual

It's some render injection group and provide conveying grouping. The end of the fuel solution scheme is to precisely insert a metered amount of hydrocarbon at the punish period. Based on the signaling device signals, the ECMs planning instrument settle when to separate each injector on and off. Whereas, the intend of the supply exploit system is to quietly save the decorous loudness of fuel at the penalize push. The gas feat system staleness also match stuff and bingle regulations. Bailiwick components are : Gas Pumps, Supply Pumps ECU, Somatesthesia Filter, Pulse Device, Hydrocarbon Injectors, and Inertia Change.

download here

Detail download here

Buzzer Burglar Alarm Circuit For Refrigerator

This circuit, enclosed in a small box, is placed in the fridge near the lamp. With the door closed the interior of the fridge is in the dark, the LDR R2 has a high resistance about 1000K ohm thus clamping IC1 by holding pin 12 high. When a beam of light enters from the opening, or the fridge lamp lights, the photo resistor lowers its resistance, pin 12 goes low, IC1 starts counting and, after a preset delay, the piezo sounder beeps for 20 sec. then stops for the same lapse of time and the cycle repeats until the fridge door closes. D2 connected to pin 6 of IC1 makes the piezo sounder beeping 3 times per second.
Buzzer Burglar Alarm Circuit For  Refrigerator
Note:
  • Delay time can be varied changing C1 and/or R3 values.
  • Place the circuit near the lamp and take it away when defrosting, to avoid circuit damage due to excessive moisture Don't place it in the freezer.
List Componet Of  Buzzer Burglar Alarm Circuit
R1    : 10K 
R2    : LDR (any type)
R3,R4 : 100K 
C1    : 10nF Polyester Capacitor
C2    : 100µF/25VD1
D2    : 1N4148
IC1   : 4060
Q1    : BC337
BZ1   : Piezo sounder (incorporating 3KHz oscillator)
SW1   : SPST slide Switch
Detail download here

Saturday, September 8, 2012

Toyota Starlet Turbo Owner Manual

Actually, that's true. In the standard form of a Toyota Starlet Turbo is one of the most discreet of machines on the road. Unlike the fast Fords, or his brother in spirit, Renault 5 GT Turbo, it looks like a little sister to manage district. But under the hood is enough firepower to the very rude railcar.

Starlet's masochistic since 1987, when it was more a matter of diodama than the car that you see here. Enamel body kit, which won the points for subtlety, packed 1295cc, single-cam, 12ventil four pot of unusual violence. Thanks to the two-stage turbocharger is handled by the Tokyo commuters move nor psychotic 111bhp 790 kg weight of the Graphic. You had to bend in it first, but 6000rpm. Maximum torque 111 lb FT arrived much earlier, in the only 3600rpm.

In the years 1990 to 1995, at that time, some more weight and become more noticeably sporting style, Starlet GT Turbo enjoyed its best incarnation and his halcyon days. A wonderfully bland style of hidden 1331cc, 16ventil twin cam four pot. Inter-cooled turbo was present and correct and put it on your eyes watering 133bhp 6400rpm. Hard hitting moment was still available around the city, the speed, and the weight crept up to 830 kg only. Sixty mph? You'll be there in 6.9 seconds, Sir. And if you want to live on the edge of it you get to 130 mph.

Download

Detail download here

Profile of the company Renault SA 2005 issue 2

Just ran the early automatic intelligence auto.com industry to the automotive industry globally since 1999. We use only experienced and acclaimed authors to publish our portfolio of automotive components sector reports and profiles. Our approach is intended to cover niche technologies sector, often at the level of the module, such as roof-systems or fuel-injection systems to give you the best available analysis at the point of a good price.

All of the messages in our growing portfolio, many in their 2nd or 3rd Edition, to give you a basic overview of the sector. Profiles of key players in each study, which assesses the technology is evolving and allows other basic intelligence, including data on market share, forecasts, and exclusive interviews with the relevant managers. In addition to the many major automotive suppliers providing a forward-looking comment profile just a car.

Source: just auto.com
Download

Detail download here

Clio Van range and technical specifications of the technical specification

Entrepreneurship, innovation and dedication. It's a combination that drives your business and philosophy, which maintains the Renault on the way to constant improvement. Witness the latest Clio Van. Updated, revised and ready for languages where the image takes you to work. Developed next to the small car superstar Clio, includes all the same backup, but in a vehicle, a practical, comfortable, hard work, brings real work style in his hand. On the road and at the place of bold, expressive lines Clio Van speaks volumes about how you all earn a living. In short, says you're a real professional.

Even at first glance looks like a dynamic command attention Clio Van. Note the front fenders with integrated, modified foglights that lend an assertive purpose. After the spotlight longer and adds body color rear spoiler. What more you want in a hustler, which is built around what is a sensational success?

The answer is ... all of it. Because once you've taken in the stunning exterior car, Clio, it's time to open the door to the Interior, which makes you feel immediately at home, where you are currently working. In fact, would hardly know that when you drive a van at all, because it's by name, creative nature of the Clio. It's what gives the compact car there with the very best of the big players

Download

Detail download here

Renault Workshop repair manual

Types of 852, the vehicle Renault 18 J8S Fuego Renault Renault Renault 20 25 30 21 Renault Safrane Espace Trafic Master Jeep.
"Methods of repair of generators, according to the data of the manufacturer in this document are based on the current, when it was prepared technical specifications. The method may be adjusted as a result of the changes introduced by the producer in the production of the various component units and accessories, from which they are made of his vehicle. "

USING THE MANUAL
In this manual are the two main parts:
-the technical specifications,
-engine implementation.
If you want to repair the part of the vehicle, refer to manually repair Workshop and technical notes for the vehicle.
UNITS OF MEASUREMENT
-All dimensions are given in millimetres (mm) (except where otherwise stated).
-Tightening torques are expressed in decaNewtonmetres (Dan). Reminder: 1, title = 1,02 m kg.
-Pressure in bar reminder: 1 bar = 100,000 Pa.

Download

Detail download here

Renault Mascot W21-760-3125 installation instructions

Special instructions for air connection
1. Cut the tubing cutter must be correctly matching the scissors (no)
2. when inserting tubing into the connection must pull in around 14 mm, to hear the click.
3. If you want to remove the tube, push on the connection, and at the same time pull the tube flange. (No tool is necessary.)
4. Watch tube is removed, it is important to trim 14 mm from the end before reconnecting.
5. it is appropriate to use LOCKTITE fittings.

Important
• Installation manual should read completely before beginning the Assembly.
• This kit does not increase G.V.W. (total vehicle weight) of vehicle for your safety and to avoid any damage to your vehicle shall not exceed the maximum load recommended by the manufacturer.
• Air bags inflate is not before the Assembly.
• Once installed, may not exceed the max and min pressure limits, improper usage or above inflation may cause the deterioration of your suspension.

Download

Detail download here

RENAULT LAGUNA ROAD TEST

Renault Laguna was gone from the Australian market of new cars since 1996, but now it's back with a new distributor and new models. Renault Australia (as part of the Alliance, Nissan/Renault) kicked off here in June 2001 with the series, which was the Clio, the Latin American and the scenic 4WD wagons runnable and Megane Convertible. Now, after some frustrating, Laguna and Laguna estate Limo arrived. Laguna saloon (read sedan, although it actually has a rear hatch!), comes in three levels of the facility. These are the permissions, permissions and Authentique LX. Laguna estate (read cars) are available in the form of Authentique and permissions.

So far, all of Australia-bound 3.0 l V6 engine, Lagunas, joined with the five-speed "tiptronic style" automatic transmission. This year, four cylinder models are due. Prices for pubs places start at $ V6 Laguna 46,990 Authentique, with the privilege of a standing $ 51,990, and permissions LX, $ 57,990. Add $ 4,000 for domains and permissions. Authentique

Equipment levels are generous, with all the dual front and Lagunas featuring front side airbags, side curtain airbags, antiblokovací with EBD and emergency brake assist, electronic stability program, traction control, climate control, air conditioning, power Windows (front) and mirrors, remote locking, cruise control, alloy wheels (4), and a trip computer, CD player. Permission Add Xenon light models, power adjustable front seats, CD player six tray, leather and velour upholstery, fog lamps, rain sensing wipers, rear side window awnings and in the warehouse.

Download

Detail download here

Renault-Riffard wing on wheels

WELL have you noticed the difference? This problem has taken another step forward to Renotes and will now wear the color on every page. With the increasing use of colors, of course, we need more high quality color pictures, which is where the members come in. send us your contributions and remember Renotes is not just about older cars, the contributions from the members of new Renaults are equally as valid. On our letters page continues the discussion about speed. This debate, due to the oft-quoted remark that, "Speed kills" is, I think I understand. Maybe more appropriate slogan, "killing for the inexperience of the ' is the fact that for years he taught people to instructors, relatively simple control test when really they should be learning to drive. There is a difference between the two.

Student can pass the test driving, without ever drove over 30 or 40 mph and without any experience of the highway. Once the investigator has been met, that same student is then let loose on the highways without further checks, or tuition fees. Our simple driving tests includes eye test to read the license plate of a stationary car, delivered at a distance; It's a complete waste of time is highlighted in a survey carried out by Specsavers and the support of Renault.

Motor Show in 2002 Specsavers eyes to 3000 tests and found that did not meet the basic vision of 157, which meant that they illegally. Save her work is 25% or in each four! Maybe it's time we had a harder look at applications for the issue of a driving licence, and for all the drivers that you want to submit to regular inspections of the optics test.

Download

Detail download here

2005-2006 FIA FORMULA 1 WORLD CHAMPIONSHIP RENAULT

Although every effort has been made to ensure that the information contained in this booklet is accurate and current as possible, Renault Uk reserves the right to change their models without warning, including their properties, specification, equipment and accessories. Brochures will be out of date or inaccurate, inevitably, in some respects, that such characteristics, equipment, specifications and accessories may be changed after the date of publication, and may differ from the description given. It is therefore necessary to check with the vendor before purchasing any product at Renault, properties, specification, equipment or vehicle accessories on the order are advertised. Date of publication: June 2007.

The fluid lines and curves. In short (Espace) or long wheelbase version (Grand Espace), with the most uncompromisingly modern design and glazed area on the market is a clear leader of the style of the Espace. Its elegance is expressed in even the smallest detail. Reengineering and cut on the rear lights chrome front fender trim gently highlights. New wheels and Trims to enhance the status of the style and the highest range of the vehicle

Download

Detail download here

AMC-Renault and a reasonable car for the times

Renault 18i was introduced in Europe in front of almost three years ago. Since then, through a series of improvements and now to the point, to debug that extremely reliable car. For the North American market 18 becomes 18i (for fuel injection) and is available as a 4-door sedan or wagon 5door. Also on our market, uses 18i optional (in Europe) 1647cc 4cylinder as the only available engine. AMC imported 18i has L-Jetronic fuel injection for the purposes of issue, any, starts immediately, the overall low maintenance warmups and a better economy.

Aluminium 4válec is conventionally located in the engine compartment and uses a long transaxte Assembly for driving the front wheels. 5Rychlostní manual transmission or an optional automatic transaxte 3rychlostní can be obtained in either of the bodywork. The engine produced at 5000 RPM 60.1 horses. /min and gives a very satisfactory performance. The response of the engine from good to excellent, in particular in the event that any equipment is a bit long before changing up. At high rpm, the engine tends to be noisy and produces more than normal vibration. But it might be considered a problem only in the case that the car was driven hard consistently. Sedan is the mass, 60/40 bias totals for comfortable 2263 pounds of spirited front drive.

Download

Detail download here

Yamaha FJR1300 owners Survey resul

Most of the owners were men aged between 50 and 64, with 50-54 contingent consists of almost 25% of the group. Model years 2005 and 2006, almost equal to the percentage of 28%. The majority (87%) bought new. Only 7.4% of the owners was model AE (electric shift with ABS), which came out in the year 2006 model. In terms of satisfaction, the owners of the models, the 2005 and 2006 satis-fied are possible: more than 95% of the owners of the years model evaluation of their wheels 4 or 5. Brand loyalty is very strong among owners: nearly 94% of all owners, said it would buy a Yamaha, on the basis of its experience with 21.9% of the previously FJR and owned other Yamahas.

Owners were less satisfied with the availability of parts and accessories: 88.6% of owners rated as above average or availability is excellent, while 22.3% rated it as average. About 10% above the low score. Several owners noted that it took weeks to get parts, with a long period of backorders. More than 80% of the owners, said they used their bikes for weekend trips. Approximately 68% of the owners use their FJRs for touring.

Our respondents are experienced riders: more than 50% owned eight or more motorcycles FJR owners before, and one owner reported owning more than 35! Previous owners Honda with 30.9%, 17.7% FJR owners owned a, BMW and 11,3% owned the Kawasakis.

Judging by your reply, he would probably be in length we added a blank, that asked you, where are your favorite tour spots. Naturally, the mountainous regions with their accompanying twisties are popular, which is evident from the pictures. It is interesting that almost a quarter of readers said that the camp during the tour. Those who travel more than 2500 miles and camped with the most: 32,9%. Definitely a good way to get your money so you can drive more miles.

Download

Detail download here

MasterGuard Hub Kit Honda 12-Yamaha:

Before the service, make sure the engine propeller blades in neutral with the ignition turned off, or disconnected, to prevent the possibility of the run and causing injury. Do not install any of the propeller thrust washer on the spot without. If the washer is not used, the move could lead to significant damage to a propeller or engine drive. Rotating prop in neutral hand make sure the prop in the full cycle of spins freely. (If you have any questions, please contact your dealer or call our customer service department.)

For the Evinrude ® and Johnson ® Outboard: (Please omit # 12035 washing machine.)
1 OEM thrust washer) is on the spot. Clean and grease shaft splines. (All marine grade fat is acceptable.)
2 Slide the HUB ASSEMBLY into) of the propeller housing from the queue.
3 Slide the propeller Assembly) of the drive shaft.
4) Frame SPACER # 12050 PROP nut and SPACER on the propeller Assembly OEM front prop nut.
5 the tightening the nut under) prop engine manual for the proper promotion and adaptation of the specifications nut torque.

Download

Detail download here

1999.5 – 2005 Volkswagen Golf/GTI 2.0L 4 Cyl. Cold Air System Installation

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
e) Install the silicone hose onto the upper end of the AEM inlet pipe with one of the 2.75” hose clamps. The upper end is the end with the AEM decal. Loosely install the second 2.75” hose clamp onto the silicone hose.
f) Feed the AEM inlet pipe into the engine bay and fender well. The lower bracket should line up with the rubber mount installed in step 3b. The upper mount should line up with the stud originally used to mount the lower intake tube.
g) Install a large fender washer and lock nut onto both the rubber mount and the stud. (Fig. 20 & 21) Refer to the following diagram for proper rubber mount installation.
h) Insert the MAF sensor into the into the silicone hose on the AEM inlet pipe. Make sure the MAF sensor is still rotated correctly in the factory position. Plug in the MAF sensor wire connector.
i) Install the AEM air filter onto the bottom of the AEM inlet pipe using the supplied hose clamp. Make sure the filter does not contact the horn or the plastic fender liner. (Fig. 22)
j) Adjust the inlet system for best fitment and snug the hose clamps and locknuts down. (Make sure that no part of the inlet system comes into contact with any part of the vehicle.)
k) Connect the factory breather hose to the AEM vacuum hose adapter. Line the clips on the plastic hose up with the flats machined into the adapter. (Fig. 23) It may be helpful to lubricate the o-ring with a small amount of clean engine oil. Use caution to avoid damaging the o-ring.
l) Install the supplied 5/8” vacuum hose section from the AEM adapter to the nipple on the back of the AEM inlet pipe with the two supplied 1” hose clamps. Route the hose in a broad arc under the AEM inlet pipe to avoid kinks. (Fig. 24)
m) Re-assemble the vehicle in the reverse order of disassembly. The large plastic cover behind the headlights that was retained by the three plastic rivets does not need to be reinstalled.
n) At this point the entire intake tube and filter can be re-adjusted for position and alignment. Make sure that no part of the AEM intake rubs anywhere along its length. Critical points to check are on the corner of the plastic battery box and at the bend in the pipe just above the air filter.


Download

Detail download here

1996 Volkswagen Golf Fuses & Circuit Breakers

The fuse panel is located under the left side of the dash board by the driver’s knee on the Cabriolet, Fox, Jetta, Rabbit and Pickup. On the Golf and GTI models the panel is located by the driver’s right knee, under the dash panel.
NOTE: On all models, fuse specifications are listed on inside of panel cover.
WARNING: Always disconnect battery ground cable before servicing “high-current fuses. It is recommended that “high-current” fuses be replaced by a qualified technician.

RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the radiator fan. The fan is temperature controlled and could start at any time even when the ignition key is in the OFF position. DO NOT loosen or remove radiator cap when cooling system is hot.


REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off all lights and accessories to avoid damaging the electrical system. Be sure to use fuse with the correct indicated amperage rating. The use of an incorrect amperage rating fuse may result in a dangerous electrical system overload.


BATTERY WARNING
CAUTION: When battery is disconnected, vehicles equipped with computers may lose memory data. When battery power is restored, driveability problems may exist on some vehicles. These vehicles may require a relearn procedure. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION section.


Download

Detail download here

2008 VOLKSWAGEN CITY JETTA

The City Jetta has undergone a revamping for 2008. The exterior look has been modified, and inside, the radio and upholstery have been changed. The steering wheel is now the same as the Jetta’s. The engine remains the same, but the automatic transmission, an option, now has six speeds rather than four. The City Jetta is offered as a four-door sedan.

Interior and trunk
Access to the front is easy. The seats are firmly comfortable, even after a long day of driving, for people of average height or less. However, there is no adjustable lumbar support. Heavily built or tall people will find the seats a bit narrow and the cushions a tad short. Thanks to the seat adjustments and tilt/telescoping steering wheel, drivers easily find a good driving position. Entering and especially exiting the back requires a bit of flexibility. The bench seat is relatively comfortable for two adults, but only if they are of average height or less, because of the limited head and leg room. Already quite spacious, cargo capacity can be expanded by folding the 60/40-split seatback. When the seatback is folded down on the cushion, the floor inclines sharply upward towards the front. To get a flat floor in this area, you have to flip the cushion and remove the head restraints before folding the seatback. The trunk is roomy, the floor flat and the storage bins on each side, very practical. The trunk opening is good and the lid opens relatively high.


Convenience and safety
The cabin is very well finished in good materials. Soundproofing is very good, though engine noise intrudes at highway speeds. There are few storage spaces and above all, no roomy centre console. Gauges and controls are well laid out, except for the heating controls, which are too low. The radio buttons are small. At night, everything except the glove compartment is illuminated.


Download

Detail download here

Volkswagen Wiring Diagram Manual Guide

Download User Manual Volkswagen Wiring Diagram. Explanation: 1. Relay location number, indicates location on relay panel. 2. Arrow, indicates wiring circuit is continued on the previous and/or next page. 3. Connection designation, relay control module on relay panel. Shows the individual terminals in a multi-point connector. 4. Diagram of threaded pin on relay panel, white circle shows a detachable connection. 5. Fuse designation. 6. Reference of wire continuation (current track number).

Download

Detail download here

1989 Volkswagen Golf I – System/Component Tests

Prior to testing separate components or systems, it is highly recommended that all procedures listed in F – BASIC TESTING article be performed. Since many computer controlled and monitored components will change voltage and resistance valves if they malfunction, it is also recommended that connector pin check diagnosis be performed.
NOTE: Testing of individual components does not isolate possible shorts or opens in the control harness of electronically controlled systems. Use an ohmmeter to isolate shorts or opens in harness. All voltage tests should be performed with a Digital Volt Ohmmeter (DVOM) with a minimum 10-megaohm input impedance, unless specifically stated different in testing procedures.

ENGINE SENSORS & SWITCHES Airflow Sensor (Cabriolet & Fox)
1) Start engine to pressurized fuel system. Turn engine off and remove intake boot from top of airflow sensor. Disconnect coil secondary wire from coil and jumper to ground.
2) Check sensor play by slowly moving plate through travel range with a magnet. Resistance should be felt. Move plate back to the rest position. There should be no resistance. If binding is felt, loosen sensor plate hold-down bolt and adjust plate to center of venturi.
3) If resistance is uneven, remove airflow sensor from housing to clean and lubricate lever assembly. If resistance is caused by control plunger, remove and clean control plunger assembly. If binding continues, replace fuel distributor.
4) Check position of airflow sensor plate. Airflow sensor plate edge must be within .075? (1.9 mm) below the narrowest section of the venturi. See Fig. 1. If not, bend sensor spring until correct specification is obtained. Ensure that there is a small gap between the sensor lever and the control plunger.


Download

Detail download here

2000-05 Volkswagen Jetta/Golf 1.8 K&N Drycharger Installation

The K&N? Drycharger included with this kit must be installed on the K&N? air filter when used with this K&N? cold air intake system. The K&N cold air intake system a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your cold air intake system to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.

Installation:
1. Turn off the ignition and disconnect the negative battery cable.
NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft coded to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code.
2. Depress the tabs on the side of the battery cover and remove as shown.
3. First disconnect the negative battery cable, then disconnect the positive battery cable as shown.
4. Disconnect the mass air sensor electrical connection as shown.
5. Loosen the hose clamp at the mass air sensor as shown.
6. Remove the air cleaner cover screws as shown.
7. Disconnect the air pump vent hose as shown.
8. Remove the air cleaner cover as shown.


Download

Detail download here

Fuel and exhaust systems – K-Jetronic fuel injection – 16 valve engines

The components of the K-Jetronic fuel injection system fitted to the 1.8 litre 16V engine are as shown (see illustrations). All procedures are the same as described in Part B of this Chapter except for those given in the following Sections.
2 Idle speed – adjustment
1. Run the engine to normal operating temperature, then check that all electrical components are switched off. Note that the electric cooling fan must not be running during the adjustment procedure.
2. Disconnect the crankcase ventilation hose (see illustration).
3. Connect a tachometer and an exhaust gas analyser to the engine.
4. If the injector pipes have been removed and refitted just prior to adjustment, run the engine to 3000 rpm several times then allow it to idle for at least two minutes.
5. Check that when the ignition is switched on, the idling stabilisation control valve is heard to buzz. If not, check the system with reference to Section 3.
6. Disconnect the wiring plug for the idle stabilisation system. This is located near the ignition coil (see illustration).
7. Allow the engine to idle, then check that the idle speed is 1000 ± 50 rpm. If necessary, remove the cap and turn the idle speed adjustment screw as required (see illustration).


Download

Detail download here

1993-1998 VW Golf III 2.0L 8-valve B&M Short Shift System Instructions

This B&M Short Shift System has been designed to work on most 1993-1998 VW 2.0L 8-valve models. It has been engineered to greatly reduce shift throw and improve shift feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Shift System. Installation of the B&M Short Shift System can be accomplished by anyone with minimal mechanical experience.

INTRODUCTION
This B&M Short Shift System can be installed in less than an hour by carefully following the instructions. Read all instructions first to familiarize yourself with the parts, tools, and procedures. This kit contains all the parts necessary to install the shifter.


STEP 1. Park vehicle on level ground, apply parking brake, place shifter in neutral, and allow engine to cool.
STEP 2. Locate transmission shift linkage on the transmission in the engine compartment (see arrow)
STEP 3. Unclip pins a and remove change rod b.
TOOL: Needle Nose Pliers G (optional).


Download

Detail download here

1998-2005 Volkswagen Passat Bentley Announcement Service Manual

This repair manual covers the 1998 through 2005 model year Passat models built on the Volkswagen B5 platform. The doityourself Passat owner will find this manual an indispensable source of detailed maintenance and repair information.

Even if you have no intention of working on your car you will find that reading and owning this manual makes it possible to discuss repairs more intelligently with a professional technician.Features: Covers Passat Passat wagon and 4motion models built on the B5 platform. Large stepbystep maintenance section. Engine and cylinder head service including timing belt and camshaft replacement. Component testing removal and installation for engine lubrication cooling and exhaust systems. Fuel supply service including fuel pump delivery and electrical checks EVAP system and mechanical and electronic throttle control (Egas). Fuel injection and ignition system component identification electrical testing technical data and throttle valve control module adaptation using the factory scan tool. Drivetrain maintenance troubleshooting adjustment and repair including hydraulic clutch gearshift linkage and axles. Repair information for ABS/EDL/ASR brake systems.


Download

Detail download here

Audi TT / VW GTI/Jetta/Golf Performance Chip Upgrade Installation Instructions

This handout is provided to guide you through the steps necessary to upgrade your vehicle with one of our performance chips. Also be aware that APR is only a phone call away should you every have any questions or concerns pertaining to any APR products.


Step 1: Park Car.
Insure car is off and key is out of ignition. Engage the parking brake. (Optional): Remove Battery Cable. Caution! Before disconnecting the battery, determine the correct coding for the anti-theft radio.
Step 2: Remove Windshield Wipers.
Remove Windshield Wipers to ease removal and installation of ECM.
Use a flat head screwdriver to remove the plastic cover from the wiper arm. Remove the wiper arms by unbolting the 13mm nut securing the wiper arms. After the nut is removed the wiper arm must be wiggled in order to remove the arm from the mount. Be sure to note the location of the wiper arm for re-instillation.
Repeat this procedure for both sides.
Step 3: Remove Factory Weather-Stripping.
Step 4: Raise Plastic Lid Over Pollen Filter.
Step 5: Remove Plastic Bracket, noting location of tabs
Step 6: Pull tab on wiring harness to the left, and remove left wiring harness.


Download

Detail download here

Friday, September 7, 2012

LDR Relay Switch Circuit

This is a LDR switch or light activated relay circuit. This circuit will let you make a switch that will be activated by light falling on a sensor. It is a very useful device and can be used in automatism’s, security systems, counters, remote controls etc. It is very sensitive, fast acting and reliable. The circuit uses a Light Dependent Resistor (LDR) as a sensor and IC LM311 to amplify the signals from the LDR and transistor 2N2222 to drive the relay which does the switching.
LDR Relay Switch Circuit
Normally the resistance of an LDR is very high, sometimes as high as 1000 Kohms, but when they are illuminated with light resistance drops dramatically. The relay on when LDR uncoverd and relay off when LDR covered. Adjust VR1 for light sensitive.LED will turn on at the same time with relay
Detail download here

Thursday, September 6, 2012

12VDC to 220VAC Inveter using IC 555

This 12VDC to 220VAC inverter circuit produces an AC output at line frequency and voltage. The 555 is configured as a low-frequency oscillator, tunable over the frequency range of 50 to 60 Hz by Frequency potentiometer R4.
The 555 feeds its output (amplified by Q1 and Q2) to the input of transformer T1, a reverse-connected filament transformer with the necessary step-up turns ratio. Capacitor C4 and coil L1 filter the input to T1, assuring that it is effectively a sine wave. Adjust the value of T1 to your voltage.
Detail download here

TDA 2616 - 1 2W Stereo Hi-Fi Amplifier Circuit

This is a circuit diagram of 2X12 W Hi-Fi Amplifier based on TDA 2616 IC which is the core part of this circuit. The TDA2616 is a stereo power amplifier IC. This amplifier IC finds applications in mains fed amplifier circuits such as stereo radio, tape and television. It has gain balance for both of the channels and hi-fi according to standards such as IEC 268 and DIN 45500. This IC has special inbuilt circuit for the suppression of noise signals at the inputs, during switch-on and switch-off. This avoids click sounds during power on and power off.
TDA 2616 - 1 2W Stereo Hi-Fi Amplifier Circuit
Simple and less number of components make this circuit suitable for portable power amplifier circuits. A well regulated and filtered +/- 12 V dual power supply is used in this circuit to provide at least 2 A continuous current. The circuit can deliver a maximum output of 12 W power on 8 Ohm speaker for each channel at +/- 12 V dual supplies. This Hi-fi amplifier circuit can complement your audio system with ceiling speakers for home theater.
Detail download here

LA3600 5 Band Graphic Equalizer

LA3600 graphic equalizer circuit shown here. This circuit very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.
LA3600 5 Band Graphic Equalizer Circuit
In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. C12 is the output capacitor and resistor R6 limits the supply current. Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5
Detail download here

Wednesday, September 5, 2012

Triac Light Dimmer Circuit

This is a simple 220V light dimmer circuit based triac can be used to adjust the brightness of mains lights about 350 watts. It also can be used to adjust the speed of AC motors. It uses a triac, diac and has a radio-frequency interference (RFI) noise suppression circuit built into it as well. Please note that this circuit cannot be used with fluorescent lights.
Triac Light Dimmer circuit
List Component of   Triac Light Dimmer circuit
R1     : 50K Pot
R2     : 15K 1/2W Resistor
C1, C2 : 0.068 250V Capacitor
L1     : Lamp To Be Controlled (up to 350 watts)
L2     : Neon Lamp
TR1    : 40502 TRIAC 
 
Note: 
  • This circuit is for 117VAC only. 220 or 240 V will burn up the circuit. L1 can be a maximum of 350 watts.
  • The circuit must be installed and used in a case. 
  • Heat sink is necessary for 40502 TRIAC 
Detail download here

Tuesday, September 4, 2012

LM1036 Stereo Tone Control Circuit

Here is a LM1036 stereo tone control circuit which build based on IC LM1036. This circuit will controll bass/treble level tone, volume and balance between right channel and left channel (input 1 and 2 ). You may use this circuit for stereo applications such as car radio, TV and audio systems, mp3 player, dvd player, ipod and more. An additional control input allows loudness compensation to be simply effected. The circuit should be works with supply voltage 9V to 15V DC.
LM1036 Stereo Tone Control Circuit
LM1036 Pinout
Each tone response is defined by a single capacitor chosen to give the desired characteristic. By changing the values of capacitor connected to tone controlling unit, you can control bass and treble levels. pin 3 and pin 18 of IC are for treble and pin 6 and pin 15 for bass.
Detail download here

Monday, September 3, 2012

2 Way Active Crossover Circuit

Here is the schematic of a 2 way active cross- over network circuit that finds a lot of application in audio amplifier systems. The circuit use a constant voltage method, means that the output of high and low frequency is summed up, and then fed back to be compared with the input to make sure this sum is equal to the input signal. This method ensure that the total response is flat, if we summed back the separated high and low frequency output.
2 Way Active Crossover Circuit
LM833 Pin-Out
You have to use 1% tolerance for the resistors to give a precise response. According to the formula, the capacitor C should be 6.6nF to give 1kHz crossover frequency, but a 6.8nF can be used because it waidely available, and the crossover frequency will be shifted to about 975Hz.
Detail download here

Saturday, September 1, 2012

DC Motor Speed Controller Using NE555 PWM Switching

The following project is a PWM fan control, It is very easy to be built and it can efficiently control all DC fans to rpm as low as 450 rpm (the lowest limit has to do with the fan type and manufacturer). It uses ONLY one 555 timer and a few other components, and it can be powered also directly from the PC power supply, from the 12 Volts line.
The 555 will create a series of PWM pulses and will be driven directly to the gate of the MOSFET. The MOSFET is chosen to be big enough to carry enough loads, up to 9.2 amperes. You can choose a MOSFET according to your needs.

The MOSFET will generate enough power so that the motor will start revolving. The capacitor across the MOSFET is the solution to the'kicking sound'. The MOSFET will send to the motor pulses according to the pulses generated from the 555. If you remove the capacitor, you will definitely hear this annoying sound. The capacitor will smooth the voltage across the motor and therefore the power driven to it will be smooth, avoiding the torque kick
Detail download here